How Do You Deflate a Kite?

July 16, 2022 3 min read

There are a few steps to fully deflate your kite. Before using it it's good to know what kiteboarding gear you need. First, close all air clips on the Leading Edge. Next, unscrew the release valve located on the lower portion of the Airflow. Roll the kite from wingtips to the center of the kite. Once deflated, it is time to roll the kite upright. Ensure the kite is free of debris. Then, lift it up to access the release valve. Don't forget to check how to pack your kite.

Precautions to Fold a Kite

There are several steps involved in folding a kite. First of all, you must find a location where the wind will be consistent and strong enough to fly your kite. You should avoid areas with trees or power lines. You can also fly your kite near water bodies, as these will provide strong winds that will help it fly higher. Be sure to use a string or flying line to keep it in the air, as this is crucial to ensuring its proper flight. Kitesurfing burns calories and it's a full-body workout and fun for everyone!

Once you have folded your kite, you must remove the line that connects it to the string. You should never spool the line. The line will be tangling if it is not properly connected to the kite. To prevent this from happening, untwist the line. You should also be sure to remove the valve nozzle. If you don't have this tool, you should make sure that your kite is dry.

Safety Release Valve on a Kite

Kite safety systems have become increasingly common over the last few years. Most 4 and 5-line kites are equipped with a safety release valve to disconnect power and depower the kite if the user becomes overpowered or loses control of it. These safety systems also function as a backup for the power line, which must be free of sand and debris to function properly. A kite killer strap is attached to the user's wrists, which pulls on the brake lines and trailing edge of the kite once the handle is released. The kite loses power and profile due to the wind, and the fifth line helps the user retrieve the kite.

Always check your kite's safety release valve before using it. If you feel the pressure in your struts, the valve will shut. If it does not, reattach all points. This prevents further problems. Also, remember to remove any bungees or struts that are around the bar ends. It is not advisable to carry an inflated kite close to the wingtips, as they can cause instability.

Checking for Tangles on Safety Lines

If you're about to deflate your kite, check the safety lines for tangles. Checking the safety lines for tangles is critical, especially if you're using a kite that is inverted. If the middle line is twisted, it may cause the kite to loop out of control. Moreover, this condition can damage the kite, so you need to avoid the wave if possible.

Always check the safety lines for tangles. You can get injured by swimming in the lines of a kite, so don't do it. If the kite tangles, it may still be flying. To detangle it quickly, hold it low to the water and disconnect the leashes. Then, let the kite deflate naturally.

Checking for Wind Direction

Before you deflate a kite, make sure to check the wind direction. Wind is always downwind from the controller, so if the wind is coming from the side, it may be difficult to tell which direction the wind is blowing. If you can see some branches, spinsocks, or windsocks, you can get an idea of which direction the wind is blowing.

The wind window is the area of the sky that covers directly overhead and the rider's peripheral vision. Kites that are flying outside of the wind window will stall, or worse, drop out of the sky. So, it's crucial to know the wind direction before you launch! If you're unsure, take a picture of this area and mark the direction of the wind. 

Also in Info

Men's Suits - Is it OK to Wear the Same Suit Everyday?

February 29, 2024 3 min read

How to Wash a Beach Mat

December 10, 2022 3 min read

Which Dog Life Jacket Is Best?

September 30, 2022 3 min read

Sign up for our Newsletter

Spin to win Spinner icon