Where Does a Leash Go on a Surfboard?

September 15, 2022 3 min read

A leash creates a small amount of drag in the water and can be tangled in underwater vegetation like kelp, preventing you from surfing. In areas with kelp, it may be best to go leashless to prevent this. A leash can also restrict your movement on the board and interfere with certain footwork.


A leash is the strap you attach to your surfboard. A surf leash can be made of different materials depending on the size and weight of your board. A thinner one is ideal for small waves, while a thick one is suitable for large waves. When choosing the leash thickness, consider how much drag you are likely to encounter in the water. The thicker one is more durable, but it will slow you down.

The leash has several attachment points, including a cuff, which attaches to your ankle. Some leashes also have a key pocket. This is not intended for use as a push to start fob. Another part of the leash is the cord, which is a polyurethane piece that connects to the rail saver.


A leash is a great way to keep your surfboard in control while you ride. It acts as a safety net in rough waves and prevents your board from slipping away from you. It's usually attached to a plug near the tail of the surfboard, and is secured to your back leg with a Velcro strap. You can attach it just above the ankle or around your calf.

Depending on the type of leash you're using, you can find a variety of places to attach it to a Surfboard. A leash plug is typically made of plastic with a metal rod. Another popular location is a loop in the fin box. Then, thread the leash cord through this loop. Once you're attached, use velcro straps to fasten the leash to your board.

Rail Saver

You've probably wondered, "Where does a leash go on a board?" The answer is somewhere near the tail of the board. This is because a leash can cause a lot of force, which can damage the tail of a surfboard. In fact, some surfboards have been carved through by leash cords. To avoid this, you should use a rail saver that's attached to the leash's cord.

A leash is a long rope that is normally made of nylon and tied around a plug at the bottom of the surfboard. A rail saver will help prevent the leash from tangling with the rails and pulling into the tail.

End of Leash

When you are surfing, you will need to tie a surfboard leash. A leash with a loop connection is the best choice. This will prevent the leash from pulling against the rails or edges of the board, which is often the cause of damage. You should use a rail saver to protect the rail and the end of the leash should be looped through it with Velcro.

It is important to properly maintain the leash and clean it after each surf session. It is also important to avoid leaving a leash tied to a board for a long time. This can cause it to twist and curl. To prevent this problem, always remember to check the condition of the rope before entering the water.

At the End of the Board

The leash is attached to the board by a cord at the end. Some surfboard leashes are coiled, and some are not. The coil prevents the leash from dragging in the water. Another type of leash is a swivel, which allows the surfer to turn freely while holding onto the board.

Leashes are an important part of surfboard safety. They help prevent you from falling and hitting rocks, boulders, jetties, and other water users. They also prevent you from going under the water in the event of an accident. They're especially useful at surf breaks that are far from shore.

The leash comes with a nylon rope. Make sure that it is not too long or too short. The rope should fit through the leash plug, so that it does not hang over the tail of the board. Otherwise, the leash cord can cut the tail during a wipeout. A surfboard's rail is very thin, and it's easy to rip if the leash cord extends past the rail.

Also in Info

Men's Suits - Is it OK to Wear the Same Suit Everyday?

February 29, 2024 3 min read

How to Wash a Beach Mat

December 10, 2022 3 min read

Which Dog Life Jacket Is Best?

September 30, 2022 3 min read

Sign up for our Newsletter

Spin to win Spinner icon